Content-type: text/html Man page of atapi_ide

atapi_ide

Section: Environments, Tables, and Troff Macros (7)
Index Return to Main Contents
 

NAME

atapi_ide - Interface for ATAPI or IDE (PC) devices  

SYNOPSIS

PCI bus CMD/Acer ATAPI/IDE adapter:
   bus pci0 at *
   bus ata0 at *
   controller scsi0 at ata0 slot 0
   controller scsi1 at ata0 slot 1
PCI bus Cypress ATAPI/IDE adapter:
   bus pci0 at *
   bus ata0 at *
   bus ata1 at *
   controller scsi0 at ata0 slot 0
   controller scsi1 at ata1 slot 0
PCMCIA bus ATA/IDE disk card:
   bus pcmcia0 at *
   bus ata0 at pcmcia?
   controller scsi0 at ata0  

DESCRIPTION

Devices commonly known for their use on PC devices as ATA or IDE devices are supported using the rz device driver. The ATA standard has also been expanded to include what are known as ATAPI devices. The rz device driver is also used for those disks and CD-ROM devices. These devices may also be known under the names EIDE, ATA-2, Fast-ATA, or Ultra-ATA.

Beacuse the ATA/IDE standard was not developed until after many of the devices that used this standard were produced, there are many devices which do not strictly comply with the standard. While it is possible some industry standard devices may appear to work, it is also possible they will cause hang or data corruption cases when used under more stressful situations. For this reason, it is recommended that only the supported devices be used. These devices have been tested and are certified for correct operation.

ATAPI/IDE controllers allow the connection of two devices. These two devices are known as the master device and the slave device. If only one device is connected, that device must be the master (slave-only configurations are not supported). When used by the rz device driver, the IDE master device is assigned SCSI id 0 for that controller. The slave device is assigned SCSI id 1 for that controller. No other SCSI ids are assigned on that controller. Most ATAPI/IDE adapters contain two channels (known as the primary and secondary). Each of these channels may contain their own master and slave devices. Therefore, a dual channel ATAPI/IDE controller may contain up to 4 devices (a master and slave pair on each channel). These 4 devices are then accessed as SCSI id 0 and 1 on each channel (therefore using such names as rz8 for the master and rz9 for the slave).

Many SCSI operations translate perfectly for use on IDE. For example, read and write operations are the same. However, many SCSI disk mode pages are emulated by the IDE device driver. For example, you can display the SCSI inquiry mode pages using the following command: % scu show inq pages pages are created by the device driver to contain the long (full IDE) form of the device name, serial number, revision, and the operational modes of the device. Only a shortened version of this information is available with the standard SCSI inquiry command. Note also that the following command: % scu show pages Shows that the SCSI mode pages contain only partial information. Only that information (such as geometry) that the drive reports to the system is able to be reformatted into these emulated SCSI mode pages. Much of the information (such as RPM) is simply not available from the drive, and therefore not accurately reported.

ATAPI devices are much more closely related to SCSI devices, and as such contain their own mode pages. Therefore, for these devices, the mode page values reported are those from the device, and no emulation is involved.

ATAPI tape devices are not supported at this time.  

FILES

/dev/disk/rz??? /dev/disk/rrz???  

RELATED INFORMATION

SCSI(7), rz(7),disklabel(8) delim off


 

Index

NAME
SYNOPSIS
DESCRIPTION
FILES
RELATED INFORMATION

This document was created by man2html, using the manual pages.
Time: 02:40:27 GMT, October 02, 2010