logo
Manual Pages
Table of Contents

NAME

na_snmp - set and query SNMP agent variables

SYNOPSIS

snmp snmp authtrap [ 0 | 1 ] snmp community [ add ro community ] snmp community [ delete { all | ro community } ] snmp contact [ contact ] snmp init [ 0 | 1 ] snmp location [ location ] snmp traphost [ { add | delete } { hostname | ipaddress } ] snmp traps [ walk prefix ] snmp traps load filename snmp traps [ { enable | disable | reset | delete } trap_name ] snmp traps trapname.parm value Note that trapname may not contain embedded periods ('.').

DESCRIPTION

The snmp command is used to set and query configuration variables for the SNMP agent daemon (see na_snmpd(8)). If no options are specified, snmp lists the current values of all variables. You use traps to inspect the value of MIB variables periodically and send an SNMP trap to the machines on the traphost list whenever that value meets the conditions you specify. The traphost list specifies network management stations that receive trap information. The priority level of a build-in trap can be found by inspecting the ones digit of the trap number sent to the traphost, or from the trap definition in the Data ONTAP MIB.
       -- 1 emergency
       -- 2 alert
       -- 3 critical
       -- 4 error
       -- 5 warning
       -- 6 notification
       -- 7 information
       -- 8 debug

OPTIONS

In all the following options, specifying the option name alone prints the current value of that option variable. If the option name is followed by one or more variables, then the appropriate action to set or delete that variable is taken. authtrap [ 0 | 1 ]
Enables or disables SNMP agent authentication failure traps. To enable authentication traps, specify 1. To disable authentication traps, specify 0. Traps are sent to all hosts specified with the traphost option. community [ add | delete ro | rw community ] Adds or deletes communities with the specified access control type. Specify ro for a read-only community and rw for a read-write community. For example, to add the read-only community private, use the following command: snmp community add ro private Currently the SNMP SetRequest PDU is not supported, so all read-write communities default to read-only. The default community for the filer SNMP agent is public and its access mode is ro. A maximum of eight communities are supported. contact [ contact ] Sets the contact name returned by the SNMP agent as the System.sysContact.0 MIB-II variable. init [ 0 | 1 ] With an option of 1, this initializes the snmp daemon with values previously set by the snmp command. It also sends a coldStart trap to any hosts previously specified by the traphost option. On a query, init returns the value 0 if the SNMP daemon has not yet been initialized. Otherwise, it returns the value 1. location [ location ] Sets the location name returned by the SNMP agent as the System.sysLocation.0 MIB-II variable. traphost [ add | delete hostname | ipaddress ] Adds or deletes SNMP managers who receive the filer's trap PDUs. Specify the word add or delete as appropriate, followed by the host name or IP address. If a host name is specified, it must exist in the /etc/hosts file. For example, to add the host alpha, use the following command: snmp traphost add alpha No traps are sent unless at least one trap host is specified. Up to a maximum of eight trap hosts are supported. On a query the traphost option returns a list of registered trap hosts followed by their IP addresses. If a host name cannot be found in /etc/hosts for a previously registered IP address, its name defaults to a string representation of its IP address. snmp traps Displays all of the user-defined traps. snmp traps [ walk prefix ] Display the current traps and their settings. If walk and prefix are specified, the command displays only traps with names beginning with prefix. snmp traps load filename Loads traps from the file filename; Each line in filename must consist of lines with the same syntax as the snmp traps command, but with the "snmp traps" omitted from the line. snmp traps { enable | disable | reset | delete } Enables, disables, resets or deletes all userdefined traps. snmp traps { enable | disable | reset | delete } trapname Enables or disables the specified trap. Or allows the specified trap to be reloaded from the trap database or deleted. Note that trapname may not contain embedded periods ('.'). snmp traps trapname.parm value Defines or changes a user-specified trap.
  Legal parms, with a description of each, are as follows:
       Parm                          Description
       var/OID
                 The MIB object that is queried to determine the trap's
                      value. All MIB objects must be specified
                      in the form snmp.OID. A list of OIDs in the
                      Data ONTAP MIB is in the traps.dat file in the
                      same directory as the MIB.
       trigger
                      Determines whether the trap should send data.
                      The following triggers are available:
                           single-edge-trigger sends data when the trap's
                           target MIB variable's value crosses an
                           a value that you specify.
                                double-edge-trigger enables you to have the trap
                           send data when an edge is crossed in
                           either direction (the edges can be
                           different for each direction.
                                level-trigger sends data whenever the trap's value
                           exceeds a certain level.
       edge-1
       edge-2
                      A trap's edges are the threshold values that
                      are compared against during evaluation to
                      determine whether to send data.
                      The default for edge-1 is the
                      largest integer and the default for edge-2
                      is 0.
       edge-1-direction
       edge-2-direction
                      Edge-triggered traps only send data when the
                      edges are crossed in one direction. By default,
                      this is up for the first edge and down for the
                      second edge. The direction arguments let you
                      change this default.
       interval
                      The number of seconds between evaluations of the trap.
                      A trap can only send data as often as it is
                      evaluated.
       interval-offset
                      The amount of time in seconds until the first trap
                      evaluation. Setting it to a nonzero value will
                      prevent too many traps from being evaluated at
                      once (at system startup, for example). The
                      default is 0.
       backoff-calculator
                      After a trap sends data, you might not want it
                      to be evaluated so often anymore. For example,
                      you might want to know within a minute of when
                      a file system is full, but only want to be
                      notified every hour that it is still full.
                      There are two kinds of backoff calculators:
                      step-backoff and exponential-backup
                      in addition to no-backoff.
       backoff-step
                      The number of seconds to increase the
                      evaluation interval if you are using a step
                      backoff. If a trap's interval is 10 and its
                      backoff-step is 3590, the trap is evaluated
                      every 10 seconds until it sends data, and once
                      an hour thereafter.  The default is 3600.
       backoff-multiplier
                      The value by which to multiply a trap's
                      evaluation interval each time it fires. If you
                      set the backoff calculator to exponential-
                      backoff and the backoff multiplier to 2, the
                      interval doubles each time the trap fires.
                      The default is 1.
       rate-interval
                      If this value is greater than 0, the samples of data
                      obtained at the interval points (set using the
                      interval parameter) for a trap variable are used
                      to calculate the rate of change. If the calculated
                      value exceeds the value set for edge-1 or edge-2
                      parameters, the trap is fired. The default is 0.
       priority
                      emergency or (in descending order of severity)
                      alert or
                      critical or
                      error or
                      warning or
                      notification (default) or
                      informational or
                      debug
       message
                      Message associated with the trap. The message could
                      be a string or of the form snmp.oid. If an OID is
                      specified, the result of evaluating that OID is
                      sent. The default message is a string that shows
                      the OID value that triggered the trap.

You can trap on any numeric MIB variable. All user-defined traps are sent with a variable binding to the userDefined trap in the Data ONTAP MIB, which has the OID of 1.3.6.1.4.1.789.0.2. The trap itself contains the source entity (the filer). The trap data contains a string of the following form: name == value
name is the name specified by the user. value is the value of its MIB object at the time the trap fires. You use standard SNMP tools to receive and examine these traps. You can enter trap parameters in any order. They are never evaluated until you specify a variable and an evaluation interval.

EXAMPLES

To define the cpuBusyPct trap and set it to point at the MIB object that returns the cumulative CPU busy time percentage of the filer, use the following command: snmp traps cpuBusyPct.OID snmp.1.3.6.1.4.1.789.1.2.1.3.0 To set the evaluation interval of cpuBusyPct to one minute, use the following command: snmp traps cpuBusyPct.interval 60 To prompt cpuBusyPct to fire whenever its value exceeds a value (which has not yet been specified), use the following command: snmp traps cpuBusyPct.trigger level-trigger You can set a firing threshold to a percentage of a returned value. The following command sets the cpuBusyPct trap's firing threshold at 90%. This means that whenever cpuBusyPct is evaluated and a GET to the MIB entry it points to returns a number in the range 90..100, the trap fires. snmp traps cpuBusyPct.edge-1 90 To cause cpuBusyPct to become active, use the following command: snmp traps enable cpuBusyPct To use a backoff and not hear about the busy percentage every 60 seconds, use the following command: snmp traps cpuBusyPct.backoff-calculator step-backoff To cause the trap to be evaluated only every 30 minutes after the first firing (60 + 1740 == 1800 seconds, or thirty minutes), use the following command: snmp traps cpuBusyPct.backoff-step 1740 To Define badfans and set its MIB object, use the following command: snmp traps badfans.OID snmp.1.3.6.1.4.1.789.1.2.4.2.0 A double-edge-triggered trap fires once when the first edge is crossed and again when the second edge is crossed. To define badfans as a double-edge-triggered trap, use the following command: snmp traps badfans.trigger double-edge-trigger To cause badfans to fire when the number of bad fans in the filer goes from zero to nonzero (it still fires if the number of fans suddenly goes from zero to two), use the following command: snmp traps badfans.edge-1 1 You can cause badfans to fire again whenever the number of bad fans in the filer becomes zero again. By default the crossing direction for the first edge is up, and for the second is down; this is what you want, so there is no need to specify the edge direction, and you use the following command: snmp traps badfans.edge-2 0 To cause badfans to be evaluated every 30 seconds, use the following command: snmp traps badfans.interval 30

FILES

/etc/hosts
Hosts name database

CLUSTER CONSIDERATIONS

The filers in a cluster can have different settings for the snmp options.

EXIT STATUS

0
The command completed successfully.
1
The command failed due to unusual circumstances.
2
There was a syntax error in the command.
3
There was an invalid argument provided.
255
No result was available.

SEE ALSO

na_partner(1), na_autosupport(8), na_snmpd(8).
Table of Contents