Man page of READCD
Section: Schily's USER COMMANDS (1)
Updated: Version 2.0
Return to Main Contents
readcd - read or write data Compact Discs
is used to read or write Compact Discs.
of the drive. Communication on
is done with the SCSI general driver
Other operating systems are using a library simulation of this driver.
Possible syntax is:
In the latter case, the drive has to be connected to the default
SCSI bus of the machine.
are integer numbers.
Some operating systems or SCSI transport implementations may require to
specify a filename in addition.
In this case the correct syntax for the device is:
If the name of the device node that has been specified on such a system
refers to exactly one SCSI device, a shorthand in the form
may be used instead of
To access remote SCSI devices, you need to prepend the SCSI device name by
a remote device indicator. The remote device indicator is either
A valid remote SCSI device name may be:
to allow remote SCSI bus scanning or
to access the SCSI device at
connected to SCSI bus # 1,target 0 lun 0.
To access SCSI devices via alternate transport layers,
you need to prepend the SCSI device name by a transport layer indicator.
The transport layer indicator may be something like
To get a list of supported transport layers for your platform, use
portable to all UNIX platforms, the syntax
is preferred as is hides OS specific knowledge about device names from the user.
A specific OS must not necessarily support a way to specify a real device file name nor a
way to specify
0 is the default SCSI bus on the machine. Watch the boot messages for more
information or look into
for more information about the SCSI configuration of your machine.
If you have problems to figure out what values for
should be used, try the
If no options except the
option have been specified,
goes into interactive mode.
Select a primary function and then follow the instructions.
Print version information and exit.
Sets the SCSI target for the drive, see notes above.
A typical device specification is
If a filename must be provided together with the numerical target
specification, the filename is implementation specific.
The correct filename in this case can be found in the system specific
manuals of the target operating system.
support, you need to use the control device (e.g.
A correct device specification in this case may be
On Linux, drives connected to a parallel port adapter are mapped
to a virtual SCSI bus. Different adapters are mapped to different
targets on this virtual SCSI bus.
option is present,
will try to get the device from the
If the argument to the
option does not contain the characters ',', '/', '@' or ':',
it is interpreted as an label name that may be found in the file
/etc/default/cdrecord (see FILES section).
Set the default SCSI command timeout value to
The default SCSI command timeout is the minimum timeout used for sending
If a SCSI command fails due to a timeout, you may try to raise the
default SCSI command timeout above the timeout value of the failed command.
If the command runs correctly with a raised command timeout,
please report the better timeout value and the corresponding command to
the author of the program.
option is present, a default timeout of 40 seconds is used.
- debug=#, -d
Set the misc debug value to # (with debug=#) or increment
the misc debug level by one (with -d). If you specify
this equals to
This may help to find problems while opening a driver for libscg.
as well as with sector sizes and sector types.
slows down the process and may be the reason for a buffer underrun.
- kdebug=#, kd=#
to modify the kernel debug value while SCSI commands are running.
- -silent, -s
Do not print out a status report for failed SCSI commands.
Increment the level of general verbosity by one.
This is used e.g. to display the progress of the process.
Increment the verbose level with respect of SCSI command transport by one.
This helps to debug problems
during the process, that occur in the CD-Recorder.
If you get incomprehensible error messages you should use this flag
to get more detailed output.
will show data buffer content in addition.
slows down the process.
Specify the filename where the output should be written or the inout should
be taken from. Using '-' as filename will cause
stdout resp. stdin.
Switch to write mode. If this option is not present,
reads from the specified device.
Scans the whole CD or the range specified by the
for C2 errors. C2 errors are errors that are uncorrectable after the second
stage of the 24/28 + 28/32 Reed Solomon correction system at audio level
(2352 bytes sector size). If an audio CD has C2 errors, interpolation is needed
to hide the errors. If a data CD has C2 errors, these errors are in most
cases corrected by the ECC/EDC code that makes 2352 bytes out of 2048 data
bytes. The ECC/EDC code should be able to correct about 100 C2 error bytes
If you find C2 errors you may want to reduce the speed using the
option as C2 errors may be a result of dynamic unbalance on the medium.
Scan all SCSI devices on all SCSI busses and print the inquiry
strings. This option may be used to find SCSI address of the
devices on a system.
The numbers printed out as labels are computed by:
bus * 100 + target
Specify a sector range that should be read.
The range is specified by the starting sector number, a minus sign and the
ending sector number.
The end sector is not included in the list, so
will not read anything and may be used to check for a CD in the drive.
Set the speed factor of the read or write process to #.
# is an integer, representing a multiple of the audio speed.
This is about 150 KB/s for CD-ROM and about 172 KB/s for CD-Audio.
option is present,
will use maximum speed.
Only MMC compliant drives will benefit from this option.
The speed of non MMC drives is not changed.
Using a lower speed may increase the readability of a CD or DVD.
Set the maximum transfer size for a single SCSI command to #.
The syntax for the
option is the same as for cdrecord fs=# or sdd bs=#.
option has been specified,
defaults to a transfer size of 256 kB. If libscg gets lower values from the
operating system, the value is reduced to the maimum value that is possible
with the current operating system.
Sometimes, it may help to further reduce the transfer size or to enhance it,
but note that it may take a long time to find a better value by experimenting
Do not truncate the output file when opening it.
Retrieve a full TOC from the current disk and print it in hex.
Do a clone read. Read the CD with all sub-channel data and a full TOC.
The full TOC data will be put into a file with similar name as with the
option but the suffix
Do not abort if the high level error checking in
found an uncorrectable error in the data stream.
Switch the drive into a mode where it ignores read errors in data sectors that
are a result of uncorrectable ECC/EDC errors before reading.
completes, the error recovery mode of the drive is switched back to the remembered
Set the retry count for high level retries in
The default is to do 128 retries which may be too much if you like to read a CD
with many unreadable sectors.
Meter the SCSI command overhead time.
This is done by executing several commands 1000 times and printing the
total time used. If you divide the displayed times by 1000, you get
the average overhead time for a single command.
Print read-speed at # locations.
The purpose of this option is to create a list of read speed values suitable
The speed values are calculated assuming that 1000 bytes are one kilobyte
as documented in the SCSI standard.
The ouput data created for this purpose is written to
Output the speed values for
as factor based on
of the current medium.
This only works if
is able to determine the current medium type.
For all examples below, it will be assumed that the drive is
connected to the primary SCSI bus of the machine. The SCSI target id is
set to 2.
To read the complete media from a CD-ROM writing the data to the file
readcd dev=2,0 f=cdimage.raw
To read sectors from range 150 ... 10000 from a CD-ROM writing the data to the file
readcd dev=2,0 sectors=150-10000 f=cdimage.raw
To write the data from the file
(e.g. a filesystem image from
to a DVD-RAM, call:
readcd dev=2,0 -w f=cdimage.raw
environment is present, the remote connection will not be created via
but by calling the program pointed to by
to create a secure shell connection.
Note that this forces
to create a pipe to the
program and disallows
to directly access the network socket to the remote server.
This makes it impossible to set up performance parameters and slows down
the connection compared to a
environment is present, the remote SCSI server will not be the program
but the program pointed to by
Note that the remote SCSI server program name will be ignored if you log in
using an account that has been created with a remote SCSI server program as
If you don't want to allow users to become root on your system,
may safely be installed suid root. This allows all users or a group of
users with no root privileges to use
in this case will only allow access to CD-ROM type drives-
To give all user access to use
chown root /usr/local/bin/readcd
chmod 4711 /usr/local/bin/readcd
To give a restricted group of users access to
chown root /usr/local/bin/readcd
chgrp cdburners /usr/local/bin/readcd
chmod 4710 /usr/local/bin/readcd
and add a group
on your system.
Never give write permissions for non root users to the
devices unless you would allow anybody to read/write/format
all your disks.
You should not connect old drives that do not support
disconnect/reconnect to either the SCSI bus that is connected to the
CD-Recorder or the source disk.
with the broken
Linux SCSI generic driver.
You should note that
uses a hack, that tries to emulate the functionality of the scg driver.
Unfortunately, the sg driver on
has several severe bugs:
It cannot see if a SCSI command could not be sent at all.
It cannot get the SCSI status byte.
for that reason cannot report failing SCSI commands in some
It cannot get real DMA count of transfer.
cannot tell you if there is an DMA residual count.
It cannot get number of bytes valid in auto sense data.
cannot tell you if device transfers no sense data at all.
It fetches to few data in auto request sense (CCS/SCSI-2/SCSI-3 needs >= 18).
A typical error message for a SCSI command looks like:
The first line gives information about the transport of the command.
The text after the first colon gives the error text for the system call
from the view of the kernel. It usually is:
unless other problems happen. The next words contain a short description for
the SCSI command that fails. The rest of the line tells you if there were
any problems for the transport of the command over the SCSI bus.
means that it was not possible to transport the command (i.e. no device present
at the requested SCSI address).
readcd: I/O error. test unit ready: scsi sendcmd: no error
CDB: 00 20 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 25 00 00 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x25 Qual 0x00 (logical unit not supported) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.002s timeout 40s
The second line prints the SCSI command descriptor block for the failed command.
The third line gives information on the SCSI status code returned by the
command, if the transport of the command succeeds.
This is error information from the SCSI device.
The fourth line is a hex dump of the auto request sense information for the
The fifth line is the error text for the sense key if available, followed
by the segment number that is only valid if the command was a
command. If the error message is not directly related to the current command,
The sixth line is the error text for the sense code and the sense qualifier if available.
If the type of the device is known, the sense data is decoded from tables
The text is followed by the error value for a field replaceable unit.
The seventh line prints the block number that is related to the failed command
and text for several error flags. The block number may not be valid.
The eight line reports the timeout set up for this command and the time
that the command really needed to complete.
If you want to actively take part on the development of cdrecord,
you may join the cdwriting mailing list by sending mail to:
and include the word
in the body.
The mail address of the list is:
Additional information can be found on:
If you have support questions, send them to:
If you have definitely found a bug, send a mail to:
To subscribe, use:
for descriptions of the following attributes:
|ATTRIBUTE TYPE||ATTRIBUTE VALUE|
This utility is part of cdrtools.
The source for cdrtools is available in the SUNWmkcdS package.
- SEE ALSO
- MAILING LISTS
This document was created by
using the manual pages.
Time: 02:39:26 GMT, October 02, 2010